SORT BY
$12.99
$12.99
Custom Restoration decals In Gold Metallic. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Every decal is lightly coated with a base lacquer for ease of installation. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results.
* Decals images above are less vibrant and not as clear as in hand. Metallic and Micro Dry inks and are water proof, smear proof inks but can be scratched ifmis-handled before sealing. No laser or lacquered inkjet used.
Applying and cutting Waterslide Decals:
Cut your decal(s), Place the decal in a bowl of luke warm water for about 10-15 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow several hours to dry. Apply your first coat of your favorite lacquer. Detailed instructions are available in a PDF and will not be added to the weight of your order.
$12.99
$12.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process.I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. Quick coat of any clear just on the decal to protect it. Fender has used this application on many vintage and some re-issue models.
There are to many variables to guarantee your results. Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. All waterslides can be scratched so care is required when mounting. Include a message for instructions and I will send them via PDF I ship in a photo-mailer and adding three paiges of notes doesn't work with the automated sorting in the mail system. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$12.99
$12.99
60's Fender Jaguar Restoration Decal in Metallic Gold. Single order includes Two decals.
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it. Fender has used this application on the SRV signature version but with their new Decal design.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$14.99
$14.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals. I recommend watching online tutorials on the installation process. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering. Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry overnight.
There are to many variables to guarantee your results, like anything else the more prepared you are for your project the better the results.
*Not Laser or Inkjet reproductions.
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 10-15 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. A small paintbrush is great to hold the edge while sliding the backing from underneath being sure to pull it slowly. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer. Directions can be emailed via a PDF and are not added to the weight of your order.
$14.99
$14.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it. Fender has used this application on the SRV signature version but with their new Decal design.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$13.99
$13.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it. Fender has used this application on the SRV signature version but with their new Decal design.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$12.99
$12.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it. Fender has used this application on the SRV signature version but with their new Decal design.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$12.99
$12.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it. Fender has used this application on the SRV signature version but with their new Decal design.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), trimming as closely as possible to your printed image. Place the decal in a bowl of luke warm water for about 20-30 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.
$14.99
$14.99
Custom Restoration decals. Micro Dry ink that is waterproof and non smearing. With your order you will receive two decals and a practice custom shop decal. Ever tear a decal, lacquer not just right for your project? then another five day wait, I was that guy. Just one of the reasons I always include a second decal with every order. I recommend watching online tutorials on the installation process and have personally found it very helpful. I always try and ship nightly. Please consider using Micro Sol and apply your decal on a glossy finish, this will help prevent silvering, Instructions for Micro Sol products are available on line as well. Micro set replaces using a few drops of water and helps the decal adhere to the surface. Micro Sol is applied after the decal is dry and smooth by dabbing lightly with a tissue. I have been using a small very soft paint brush to liberally apply Micro Sol and leave it wet to dry. It does a great job in thinning out the edges and melts the decal to the surface for a lack of a better word. My experience with these products have allowed me to be very content with the on top application and a quick coat of any clear just on the decal to protect it.
There are to many variables to guarantee your results, Like anything else the more prepared you are for your project the better the results, I posted a tutorial link below that I liked better than some. I will be posting a video soon of my own application and some techniques that customers have shared.
* Decals images above are less vibrant and not as clear as in hand. I am working on improving the image quality especially for mobile apps. Decals are printed with Metallic and Dye Sublimation inks and are water proof, smear proof inks. No laser or lacquered inkjet used.
https://www.youtube.com/watch?v=PkawGOSFjWQ
Applying and cutting Waterslide Decals:
Cut your decal(s), Place the decal in a bowl of luke warm water for about 10-15 seconds until the decal will slide onto your work surface, I have been taking it out and removing any excess water and leaving it sit 10 seconds. You can test if its ready by lifting it, from the bowl and moving it between your thumb and finger to see if it slides, . Place decal edge to where you want it and slide the underside away from the decal. Make sure your surface is a little wet, (couple drops smoothed out with your finger) to much will not allow the decal glue to adhere properly, use either water or a wetting solution such as Micro Sol or Micro set. Please allow a few hours to dry. Apply your first coat of your favorite lacquer.